Comments for DevFor8.com

Comment on Mav2Duplex by admin

admin — Sun, 07 May 2017 06:14:05 +0000

Teensy-LC using completely different processor than small duinos. Unfortunatelly this processor is not supported. I am working on support for AtMega32U4 as it started to be common in small ones but CortexM0 is not on my list

Comment on Mav2Duplex by Anthony

Anthony — Sun, 07 May 2017 01:36:37 +0000

Hi, I’m trying to compile but getting lots of errors. I was using Arduino 1.8.2 and I revive a simple message of :- can not compile for this board…

Installed Arduino 1.0.6 and I receive pages of errors.

Board= Teensy-LC
Any chance of a hex file please?

Comment on BT Terminal for Windows Phone 8 by Ondřej

Ondřej — Sat, 25 Mar 2017 05:54:51 +0000

OK, i found it, I have to se set socket to null

Comment on BT Terminal for Windows Phone 8 by Ondřej

Ondřej — Fri, 24 Mar 2017 17:10:15 +0000

Hi,
maybe it is stupid question but what you set null?

Thank you for the answer.

Comment on Mav2Duplex by admin

admin — Wed, 24 Jun 2015 11:40:46 +0000

Telemetry output needs to be enabled. You can do it with “Enable OSD” in Mission Planner as OSD using same data as Mav2Duplex. 15 sensors is correct. Can you send pictures of problem symbols to info@devfor8.com ?

Parameters are problem because each person prefers different set of them.

Look at http://www.rcgroups.com/forums/showthread.php?t=2112910 , there is discussion about parameters and also other users with DC-16 so you can discuss it with them.

Comment on Mav2Duplex by Helmar

Helmar — Wed, 24 Jun 2015 06:58:14 +0000

Hi, ive still little trouble with the telemetry data. If i start the copter there is no telemetry
coming through. I always need to connect it to USB to my PC after i disconnect there is
some telemtry coming through until next power up.

Im using a DC-16 and APM 2.6. The DC16 reports 15 Sensors, is this correct ?!
The virtual JetiBox of my DC-16 shows some more Infomation like fligkt mode, where i cant find a sensor for. Sometimes the JetoBoxrandom symbos like ? and ° in places
where is does not belong .

I think im missing some information about the settings i need to do at the APM
has someone a working setup and can tell me which parameters are important for the mav2duplex to work propperly ?!

thnx
Helmar

Comment on Mav2Duplex by Helmar

Helmar — Mon, 22 Jun 2015 19:49:46 +0000

well, after i amed tho copter once, im getting now voltage an current, so mabe its just working during flight ?!
But what im missing atm is the GPS data, everything 0 but my gps led tells me it has a 3D FIX …

Comment on Mav2Duplex by Helmar

Helmar — Mon, 22 Jun 2015 19:31:03 +0000

Hi, thnx for this nice little tool
i just have a question. im using an APM 2.6 with FW 3.2.1
it seems to work so far with the MAV2Duplex, but a few things are strange.
i had to connect hte Mav2Dupleyx not to RX of the APM but to TX, which made
sence to me since i want to receive data from the APM so APM has to transmit.
Well, im getting some data, e.g. that im missing a 3D Fix, YAW, Roll, PIT aso
also the Flight modes are displayed, but what im not getting is battery voltage and current (power -1V, -1A 0mAh). But in the Mission Planner its been shown propperly
when i connect via USB
So i dont know if those values are simply not transmitted, or its not beening processed by Mav2Duplex
Ill have a look in the code too, but maybe you already know what might be the problem….
thnx
Helmar

Comment on Mav2Duplex by admin

admin — Wed, 10 Jun 2015 15:03:26 +0000

Busy now, send me not to info@devfor8.com during next week and we will see what we can do

Comment on Mav2Duplex by Rob Thomson

Rob Thomson — Wed, 10 Jun 2015 13:58:13 +0000

Hello

Any chance of an arduino hex?

Compiling this seems to be a bit of a mess!

Rob